Found a video with mods would make a great fret saw.
Tags:
Hi Hooch, thanks for sharing. If I may comment. That would be a good idea for a dedicated fret slotting saw as you would not have scrap off cuts. With the unit as shown I would be concerned that an offcut may fall onto that exposed blade and fire it back at the opporator. But that's me possibly being over carefull.
Our state has just allowed free travel within the state, borders still closed, so we drove 500klm to spend time with family. Good to get away from the workshop. But now it will be good to get back.
Taff
Hey Taff, being drill powered I wouldn't be too concerned about throwback. My thoughts were chucking in the small dremel sized sawblades, building a better engineered (same idea) frame and slide table. I'm currently in the middle of some life changing situations(nothing healthwise) that has put everything on hold for awhile. When the dust settles I may have a decent place to butcher wood in. This is being a long slow process but should have a great outcome! At this moment life for us is turned upside down, but like all journeys, you take one step at a time!
Hope all works well for you Hooch.
Good luck in whatever comes your way.
Ray
Thanks Ray, the wife and I are making major decisions that has us running around like madmen. All is good, Just stressful as hell!
Thanks Ray, the wife and I are making major decisions that has us running around like madmen. All is good, Just stressful as hell!
Hi Hooch, just got back from the family visit and into the workshop tomorrow. I feel safe now, Ha ha.
Sorry to hear you're battling at the moment, hope all works out well for you.
A problem I faced using a small diameter saw blade was finding a motor that that was smaller in diameter than the sawblade, so they would both fit under the saw table and leave room for adjustment. This is not so much of a problem if using a shaft, pully and belt drive set up. But the pulley has to be smaller than the saw blade.
In the end I used a bench grinder with a flattened top. This gave me about 20mm of rise and fall of the table for a varied cutting depth.
Taff
Taff "You just have to be so negative"LOL. Taff glad you marked yourself safe, did you use protection? :-) On eBay or Amazon there was/is a saw setup that uses pulley system. I question the speed of the drill, my jewlers lathe has a sewing machine motor that spins up nice and has plenty of power. After the move and the rest of the BS is over I'll investigate it more. Man I can't wait, a new place, some extra money(not much)to play with, new car and a light at the end of the tunnel! I just hope some a hole doesn't turn it off before I get there! LOL
On a different note. My acoustic guitar(Kona K1) has the strings separating the bridge from the body, what should I do about it? If you don't minding me asking. I loosened the strings to relieve the pressure. Should I squirt glue under it and clamp it, screw it back down from inside the body? I just got it 3-4 months ago from a friend who's husband recently died. I bought it just to help out with the intention of reselling it down the road, but I like the sound of it and decided to keep it and learn to "play" at it. Bu since I have to break it down to repair it, I'm going to install a rod pickup under the bridge and a preamp/equalizer. Any words of wisdom would be greatly appreciated Yoda. Later my friend.
hey Hooch, forgive me for sounding negative, but I'm not really, just pointing out my experience on the fretting saw subject. But I have just for fun, un tested and properly thought through come up with a fretting saw using small saws that could work. Later.
Your bridge problem. What I do and consider..... The short version.....
1- What caused the bridge to let go. Bad gluing in first place - Bridge glued to lacquered surface - Brace let go inside top - Bowed up top - soft timber bridge bowed - guitar got hot causing many of the above.
2- Remove bridge. You may need heat to soften remaining glue. I can get 90% of bridges off cold. Rectify any or all of the above. Remove lacquer and old glue, level top, clean bridge of glue, radius bottom of bridge to suit radius of top if required and flatten top if bowed up.
3- Replace bridge. Have clamps, glue [titebond], gluing cauls ready. Do a dry run, no glue, first. Use bridge pins x 2 to relocate bridge. Spread glue evenly on bridge, NOT a wiggly snake of glue. Clamp down
4- If I am unsure if the joint surfaces will bond reliably due to unevenness I will use two 1/8" bolts as insurance. These are recessed into the bridge and plugged with a corresponding timber, normally rosewood or ebony and do not show.
HOWEVER.....you could squirt glue into the gap and use the bolt method. Its your guitar and you are not charging a customer for the job.
I'm POSITIVE either way will work
Cheers Taff
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray May 7. 11 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans May 5. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!