Hi guys - Dogleg Steve here - firstly I hope that you have enjoyed the music and videos that I have posted on the site!
I play 4 string Cigar box in a picking style and want to have a go at building my own custom CBG this year and also later an electric guitar.
The thing that concerns me is the fretting of the fretboard - how to do it and how to do it accurately.
Any advice on procedure and tools to buy would be greatly appreciated from you master builders out there.
Thanks Guys - keep on picking (or sliding) !
Tags:
good advice thank you buddy
And if you want to know the nitty gritty of it all (and get a nice headache for free at the same time) you might want to check this out
http://www.luth.org/images/web_extras/al116/MagliariFretComp.pdf
Sadly, the site doesn't give coupons for free Tylenol ;-)
that's a very interesting read - if not a bit scientific for my simple musician brain! But thank you for forwarding me that Francois.
I would suggest spending a bit of time and a small amount of money tapping some bits of fret wire into an offcut of fretboard wood before you start on your custom job, just to get the feel of it.
Also, as was suggested before, measure each fret from the nut, not the previous fret, to avoid error stack-ups. I use something like this calculator for distances, although I seem to remember one that offered compensated or non-compensated options:
https://www.manchesterguitartech.co.uk/fret-and-nut-calculators/fre...
Lastly, if you are going to taper the fretboard, cut the slots first. It's a lot easier marking and cutting slots in wood with parallel sides. I know this from my own errors.......
Put them wherever you want then just play slide. kiddin
A fret saw cost $40
a 18in. ruler in 100th cost $20
4 in. square $8
X-acto Knife $6
Lay your ruler on the fret board a 1/4 in. from one edge clap it down, go to Stew Mac and use the Fret calculator for your scale length and mark the fret board with the x-acto knife use reading glasses. Then use the fret saw and square to cut the fret slot on the x-acto mark, I usually widen the x-acto mark with the fret saw first.
The method I use to mark where the frets go is to use an existing guitar. I lay a strip of masking tape taught over the frets and mark the center of each fret with a small cut of an xacto knife. I gentle pull up the tape and lay it on my CBG fret board. Transfer the marks and behold, math free fret lines. Of course measure 7 times and cut once is a good thought when cutting for frets.
I took this method a step further many years ago........
Lay the tape after marking it on a narrow aluminium strip, mark the strip along one edge and slowly and carefully put saw cuts with a hacksaw at those positions. Next time lay the alum strip on the fingerboard and mark it by pushing an exacto knife into the noched saw cuts and into the fingerboard.
You can use the other edge for a different scale. I have 10 or more alum strips used this way.
Taff
Very nice, especially if you are making many. I seem to make one every 2 years or so . . . .
C. B. Gitty Fret Marking Templates
I use these and they are accurate and easy for someone like me to understand.
Can't go wrong.
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray May 7. 11 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans May 5. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!