Like many, Shane's post/challenge put my creative side into overdrive. I had made some attempts at a thinner pickup but really didn't like the way my experiments turned out. A lot of time and learning has passed since these early experiments. What I have learned in the last couple of years has to do with why some parts of pickup design just doesn't directly translate when you make them smaller. There are a bunch of reasons that a 3 pole single coil pickup wound with the same number of turns, same magnet and wire just doesn't sound quite like its larger 6 string version.
So I rolled up my sleeves and went back to do some research into the style of pickup that Shane outlined in his video. After that, a bit of searching for materials and then some calculating. What I decided was to go with C5 ceramic magnets and 42 gauge heavy build wire.
Here is the quick drawing I put together that includes the bobbin and nickel silver cover template.
As to the bobbin material I used .020 vulcanized fiberboard I purchased from McMaster Carr. This made the pickup .010 thicker but the .015 material I tried just wasn't stiff enough. I cut the material and trimmed and sanded the edges so the wire would be less prone to getting caught. I also used a wet stone to grind the sharp corners off of the magnet.
A quick little bit of super glue and the whole assembly goes together really quick.
One benefit of using this thin forbon type of material is that the bobbin will just be held in place by the magnet to the steel platten on my winder. No double sided tape needed. I just used some blue painters tape to hold the starting part of wire in place and I was ready to wind.
Here is the wire I used. I got this spool as surplus. I use it in place of some of my more expensive wire when in the prototype stage. Not that it is much different than what I normally use, I just don't feel as bad when I have to trash some of the early work because the wire was cheap.
The second coil is done. The first one was done with a bobbin that was cut slightly oversize so I could confirm max number of turns first. This second bobbin was 1"x2" and was wound to just over 4600 turns and has a DC resistance of 2.7k. Just to put the size into perspective here it is place on a standard business card.
I used a couple of small squares of copper tape to solder the wire to a wire lead and tested. Then soldered the lead to a 1/4 jack and went about seeing what it sounds like. This is all pre potting at this point but overall, the pickup has a decent sense of balance with bass and top end.
I taped it to a folded index card and slid it under the strings of my favorite 4 string. Overall I like the tone. I'll need to wax pot it and then find a better way to install it into something before I attempt any loud volume or distortion. That said, I am pleased with this early build. Keep in mind, I find it harder to get good clean tones I like than overdriven and this one has a nice clean sound.
Here is the list of materials.
.020 vulcanized fiber board McMaster Carr
.375x.250x1.5" C5 grade magnet All Magnetics
42 gauge heavy build wire Surplus Sales of Nebraska
I've ordered nickel silver to make covers. I'll post picture once it comes in and I get one done.
Comment
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray May 7. 11 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans May 5. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!
You need to be a member of Cigar Box Nation to add comments!
Join Cigar Box Nation