If you haven't read the last instalment:
http://www.cigarboxnation.com/profiles/blogs/my-first-2-weeks-of-pi...
...so, the problem I was left with was that I hadn't grounded the strings and both my tailpiece and bridge are made of wood (and bone, neither great conductors!)
I decided to go for a pretty drastic solution. Here is the problem:
I took the strings off and took a saw to to the tailpiece... Here is my solution:
This is part of a hanging fixture ( one of the advantages of working in a department store, few though they are), I used a Dremel to cut it to the right size and drilled a few holes to mount it to the back of the guitar and 3 to hold the string ferrules. I have used bike spoke nipples for these. At 20p each at my local bike shop they're a lot cheaper than real string ferrules!
The idea was to solder a wire to the inside of the tailpiece and connect it to the ground on the back of the volume pot. What I hadn't considered is that it's bloody difficult to solder to stainless steel. I didn't have any flux to hand so I cheekily superglued a strip of copper foil tape to the tailpiece and soldered the wire to that... hopefully this will work!
So here's the new tailpiece. I actually never liked the original so wasn't too sad to see it go. The sound still seems to be just as nice so I'll take that as a success...
I soldered the wire onto the back of the pot and checked all the connections. I plugged it in and the loud continuous buzzing had all but gone! I now had a slight buzzing which went away when I touched the strings... after sending myself mad Googling this for a couple of hours I found a lot of conflicting advice, mainly:
Now I'm perfectly ready to accept that I'm not very good at soldering, as I have no previous experience with it. However I figure that if everything works, the soldering should be fine, right?
I eventually decided to believe number 2. I noticed that there was very little hum when I left the guitar in the middle of the room, and stood away from it. I also noticed that not having my amp plugged into a socket with a PC, Laptop and a baby monitor made a big difference. If anyone reading this has any other ideas I'd love to hear them!
So, I still had one last trick up my sleeve - my copper foil tape. I thought I'd give it a try on one of the new pickups I made following (I thought) Bob Harrison's suggestion.
So I have potted the coil, wrapped it in a few layers of plumbers' tape, and then wrapped in a layer of copper foil. I then ran a jumper lead from the ground connection (start of the coil) and connected it to the foil. I also used a little lump of solder to seal the foil shut in case the glue deteriorates over time.
Somewhat foolishly, I whacked the pickup in the guitar without checking it first... when I plugged it in, it didn't work. No signal, some buzz, but definitely no sound coming from the strings. Without really bothering to figure out why, I took it out and removed the copper foil (trying to grasp electronics by this point was making my head hurt). After ruminating on this over the last couple of days, I think that maybe I shouldn't have connected the ground wire to the foil and the start of the coil. If the ground is the path of least resistance, maybe I have just forced the current directly to ground... again, any feedback on this would be appreciated!
Sure enough, after removing the foil and the jumper lead, the pickup worked again. I strung it up, closed the access panels and called it a day. Some noise, perhaps, but hardly too offputting for a first attempt!
So there it is! Reasonably happy with it - will post some vids soon. Next step is to start messing around with tone pots and capacitors!
...and here's a video - let me know what you think!
Comment
In the video the pickup sounds awesome, with the buzz/hum you need to check if your home electrical installation are grounded or no, and if the amp (pre and power) are grounded too, and one more, make sure if the cable that you use to plug the guitar to the amp is shielded. For the output of the pickup, more turns and more magnetic material will rise the inductance, that will rise the voltage, if Alnico V don't are enough, try ceramic magnetics. By the way, grate job. Let's Rock!
Richey, just checked out this blog. Very nice work! I'm thinking of giving this a try as well. Any suggestions on the best gap between the magnets and the gitty strings? (I guess it all depends on magnet strength, number of turns, etc.) Still, any general guidelines would be great!
ah should have read part two ...nice playing too..
Thanks
Yes, the copper tape makes solder adhere better. I also use small brass ferrules like seen on regular pickups when the lower bobbin material I use is thin enough.
You nailed it Scott, and that's a very fine looking pickup you have there! Have you wrapped the start and ends of the coil in copper foil to make an easier connection?
Thanks for the feedback guys. Smilingdog - if you have any questions, just let me know, I think I've pretty much made every mistake possible by this point! Boxy - you're welcome to it, not my idea, but it works a charm!
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray May 7. 11 Replies 0 Likes
Started by Bill Andy in Performances, How to Play, Lessons, Concerts. Last reply by Taffy Evans May 5. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by Southern Ray Apr 26. 8 Replies 1 Like
Started by Southern Ray in Other stuff - off topic, fun stuff, whatever. Last reply by Southern Ray Apr 26. 6 Replies 0 Likes
Started by J. D. Woods in Performances, How to Play, Lessons, Concerts. Last reply by BrianQ. Apr 25. 4 Replies 0 Likes
Started by Rich Butters in Building Secrets, Tips, Advice, Discussion. Last reply by Crazed Fandango Apr 22. 4 Replies 0 Likes
Started by Nomad Jack in Performances, How to Play, Lessons, Concerts. Last reply by J. D. Woods Apr 17. 7 Replies 2 Likes
Started by Moritz Voegeli in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 14. 6 Replies 2 Likes
Started by Timothy Hunter in Other stuff - off topic, fun stuff, whatever. Last reply by Timothy Hunter Apr 10. 14 Replies 3 Likes
Started by Tom T in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 9. 9 Replies 0 Likes
Started by Southern Ray in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Apr 4. 7 Replies 1 Like
Started by Timothy Hunter in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 27. 1 Reply 2 Likes
Started by Taffy Evans in Building Secrets, Tips, Advice, Discussion. Last reply by Southern Ray Mar 10. 1 Reply 3 Likes
Started by Cigar Box Nation in Feature Articles. Last reply by BrianQ. Mar 9. 4 Replies 3 Likes
Started by Ghostbuttons in Building Secrets, Tips, Advice, Discussion. Last reply by Timothy Hunter Mar 9. 5 Replies 1 Like
Started by Justin Stanchfield in Building Secrets, Tips, Advice, Discussion. Last reply by Taffy Evans Mar 8. 6 Replies 0 Likes
Started by Ken I in Building Secrets, Tips, Advice, Discussion. Last reply by Brian partington Mar 8. 8 Replies 0 Likes
Started by Southern Ray in Cool gear discussion - that's not cigar box related. Last reply by Southern Ray Mar 6. 5 Replies 0 Likes
Started by Taffy Evans in Other stuff - off topic, fun stuff, whatever. Last reply by Taffy Evans Mar 5. 4 Replies 2 Likes
Posted by Vlad on March 31, 2024 at 11:48pm 0 Comments 1 Like
Posted by Vlad on March 6, 2024 at 2:32am 5 Comments 2 Likes
Posted by billy jones bluez on February 28, 2024 at 2:09pm 0 Comments 0 Likes
Posted by billy jones bluez on February 17, 2024 at 11:00pm 0 Comments 0 Likes
Posted by Vlad on February 11, 2024 at 1:06am 1 Comment 1 Like
© 2024 Created by Ben "C. B. Gitty" Baker. Powered by
Cigar Box Nation is presented by C. B. Gitty Crafter Supply, your one-stop-shop for Cigar Box Guitar parts and accessories!
You need to be a member of Cigar Box Nation to add comments!
Join Cigar Box Nation